Настольная книга террориста
Шрифт:
7) Stir the mixed acids and glycerine for the first ten minutes of nitration, adding ice and salt to the ice bath to keep the temperature of the solution in the 100 ml beaker well below 30 degrees centigrade. Usually, the nitroglycerine will form on the top of the mixed acid solution, and the concentrated sulfuric acid will absorb the water produced by the reaction.
8) When the reaction is over, and when the nitroglycerine is well below 30 degrees centigrade, slowly and carefully pour the solution of nitroglycerine and mixed acid into the distilled water in the beaker in step 1. The nitroglycerine should settle to the bottom of the beaker, and the water-acid solution on top can be poured off and disposed of. Drain as much of the acid-water solution as possible without disturbing the nitroglycerine.
9) Carefully remove the nitroglycerine with a clean eyedropper, and place it into the beaker in step 2. The sodium bicarbonate solution will eliminate much of the acid, which will make the nitroglycerine more stable, and less likely to explode for no reason, which it can do. Test the nitroglycerine with the litmus paper until the litmus stays blue. Repeat this step if necessary, and use new sodium bicarbonate solutions as in step 2.
10) When the nitroglycerine is as acid-free as possible, store it in a clean container in a safe place. The best place to store nitroglycerine is far away from anything living, or from anything of any value. Nitroglycerine can explode for no apparent reason, even if it is stored in a secure cool place.
3.14 PICRATES
Although the procedure for the production of picric acid, or trinitrophenol has not yet been given, its salts are described first, since they are extremely sensitive, and detonate on impact. By mixing picric acid with metal hydroxides, such as sodium or potassium hydroxide, and evaporating the water, metal picrates can be formed. Simply obtain picric acid, or produce it, and mix it with a solution of (preferably) potassium hydroxide, of a mid range molarity. (about 6-9 M) This material, potassium picrate, is impactsensitive, and can be used as an initiator for any type of high explosive.
3.2 LOW-ORDER EXPLOSIVES
There are many low-order explosives that can be purchased in gun stores and used in explosive devices. However, it is possible that a wise wise store owner would not sell these substances to a suspicious-looking individual. Such an individual would then be forced to resort to making his own low-order explosives.
3.21 BLACK POWDER
First made by the Chinese for use in fireworks, black powder was first used in weapons and explosives in the 12th century. It is very simple to make, but it is not very powerful or safe. Only about 50% of black powder is converted to hot gasses when it is burned; the other half is mostly very fine burned particles. Black powder has one major problem: it can be ignited by static electricity. This is very bad, and it means that the material must be made with wooden or clay tools. Anyway, a misguided individual could manufacture black powder at home with the following procedure:
MATERIALS EQUIPMENT ~~~~~~~~~ ~~~~~~~~~ potassium clay grinding bowl nitrate (75 g) and clay grinder
or or sodium wooden salad bowl nitrate (75 g) and wooden spoon sulfur (10 g) plastic bags (3) charcoal (15 g) 300-500 ml beaker (1) distilled water coffee pot or heat source
1) Place a small amount of the potassium or sodium nitrate in the grinding bowl and grind it to a very fine powder. Do this to all of the potassium or sodium nitrate, and store the ground powder in one of the plastic bags.
2) Do the same thing to the sulfur and charcoal, storing each chemical in a separate plastic bag.
3) Place all of the finely ground potassium or sodium nitrate in the beaker, and add just enough boiling water to the chemical to get it all wet.
4) Add the contents of the other plastic bags to the wet potassium or sodium nitrate, and mix them well for several minutes. Do this until there is no more visible sulfur or charcoal, or until the mixture is universally black.
5) On a warm sunny day, put the beaker outside in the direct sunlight. Sunlight is really the best way to dry black powder, since it is never too hot, but it is hot enough to evaporate the water.
6) Scrape the black powder out of the beaker, and store it in a safe container. Plastic is really the safest container, followed by paper. Never store black powder in a plastic bag, since plastic bags are prone to generate static electricity.
3.22 NITROCELLULOSE
Nitrocellulose is usually called "gunpowder" or "guncotton". It is more stable than black powder, and it produces a much greater volume of hot gas. It also burns much faster than black powder when it is in a confined space. Finally, nitrocellulose is fairly easy to make, as outlined by the following procedure:
MATERIALS EQUIPMENT ~~~~~~~~~ ~~~~~~~~~ cotton (cellulose) two (2) 200-300 ml beakers concentrated funnel and filter paper nitric acid blue litmus paper concentrated sulfuric acid distilled water
1) Pour 10 cc of concentrated sulfuric acid into the beaker. Add to this 10 cc of concentrated nitric acid.
2) Immediately add 0.5 gm of cotton, and allow it to soak for exactly 3 minutes.
3) Remove the nitrocotton, and transfer it to a beaker of distilled water to wash it in.
4) Allow the material to dry, and then re-wash it.
5) After the cotton is neutral when tested with litmus paper, it is ready to be dried and stored.
3.23 FUEL-OXODIZER MIXTURES
There are nearly an infinite number of fuel-oxodizer mixtures that can be produced by a misguided individual in his own home. Some are very effective and dangerous, while others are safer and less effective. A list of working fuel-oxodizer mixtures will be presented, but the exact measurements of each compound are debatable for maximum effectiveness. A rough estimate will be given of the percentages of each fuel and oxodizer:
oxodizer, % by weight fuel, % by weight speed # notes ============================================================== potassium chlorate 67% sulfur 33% 5 friction/impact
sensitive; unstable ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ potassium chlorate 50% sugar 35% 5 fairly slow
charcoal 15% burning; unstable ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
potassium chlorate 50% sulfur 25% 8 extremely
magnesium or unstable!
aluminum dust 25% ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ potassium chlorate 67% magnesium or 8 unstable